Document Type : Original Article
Authors
Department of Textile Engineering, Yazd University
Abstract
Glass fiber reinforced gypsum composites are new building materials that have been used in covering interior walls. Reinforcement by means of woven fabrics as a three dimensional material is an alternative to the use of short fibers. The application of appropriate fabrics can improve mechanical properties of gypsum composites. The aim of this research article is to investigate the effect of the application of mesh fabrics on mechanical properties of gypsum composites. To do so, three types of fabrics made of E-glass yarns with leno texture - to strengthen the warp and weft of the fabric in the gypsum mixture- were used. Bending, tensile and compression tests were carried out on them, and then statistical analyses were performed on the data. The results showed that the bearing capacity of compressive load in gypsum composites strongly depends on the joint between the layers of fabrics and mortar. The strength of the fabric plays an important role in the bending behavior of composites and the joint between the yarns of the fabric and mortar is the effective factor in the tensional load capacity.
Keywords
Main Subjects
1991, pp. 62-70.
[2] P. Padevet, P. Tesarek and T. Plachy,” Evolution of mechanical
properties of gypsum in time,” Int. J. Mech., vol. 5, no. 1, pp.1-
9, 2011.
[3] M. Ranjbaran, “Glass fiber production technology,” 1st ed.,
Tehran, 2009, pp. 123-150.
[4] J. Bijen and C. Vanderplas, “Polymer-modified glass fibre
reinforced gypsum,” Mater. Struct., vol. 25, no. 2, pp.107–114,
1992.
[5] M. Singh, and M. Garg, “Glass fiber reinforced water-resistant
gypsum-based composites,” Cement Concrete Comp., vol. 14,
no. 1, pp.23–32, 1992.
[6] C. Verbeek, and W. Du Plessis, “Density and flexural strength
of phosphogypsum–polymer composites,” Constr. Build. Mater.,
vol.19, no. 4, pp.265–274, 2005.
[7] A. Mohandesi, A. Sangghaleh, A. Nazari, & N. Pourjavad,
“Analytical modeling of strength in randomly oriented PP and
PPTA short fiber reinforced gypsum composites,” Comp. Mater.
Sci., vol.50, no. 5, pp. 1619–1624, 2011.
[8] E. William, and M. Newton, “Glass Fiber Lath in Exterior
Portland cement Plaster (Stucco),” presented at the 11th
Canadian Conf. on Building Science and Technology, Banff,
Alberta, December 14, 2007.
[9] G. Huang, and Z. Zuo, “Compressive behaviours and failure
modes of concrete cylinders reinforced by glass fabric,” Mater.
Design, vol. 27, pp.601–604, 2006.
[10] D. Zhu, M. Gencoglu, and B. Mobasher, “Low velocity flexural
impact behavior of AR glass fabric reinforced cement
[11] A. Peled, S. Sueki, and B. Mobasher, “Bonding in fabric–cement
systems: Effects of fabrication methods,” Cement Concrete Res.,
vol.36, pp.1661–1671, 2006.
[12] D. Zhu, A. Peled, and B. Mobasher,” Dynamic tensile testing of
fabric–cement composites,” Constr. Build. Mater., vol. 25, no.
1, pp. 385-395, 2011.
[13] Exterior finishing system and building wall containing a
corrosion-resistant enhanced thickness fabric and method of
constructing same by E. William, M. Newton and W. Tucker.
(2011, mar. 8). Patent D 7902092.
[14] M. Varsei, S. Shaikhzadeh Najar, M. Hosseini, and M. Seyed
Razzaghi, “Bending properties of fine-grained concrete
composite beams reinforced with single-layer carbon/
polypropylene woven fabrics with different weave designs and
thread densities,” J.Text. I., vol. 104, no. 11, pp.1213-1220,
2013.
[15] R. Winston, & C. Syrakvfsky, “Mechanics of composite
materials (Composite structures behavior)”, (Translation B.
Farshy, G. Alizadeh Kaklr, Gh. Khbazyan), Amir Kabir
University Press, 1st ed., Tehran, pp. 52-67, 2009.
[16] J. Aghazadeh Mohandesi, A. Sangghaleh, A. Nazari, N.
Pourjavad, “Analytical modeling of strength in randomly
oriented PP and PPTA short fiber reinforced gypsum
composites”, Com. Mater. Sci., vol. 50, pp.1619–1624, 2011.
[17] S. Gutiérrez, M. Alonso, J. Gadea, A. Rodríguez & V. Calderón,
“Compatibility between gypsum and polyamide powder waste to
produce lightweight plaster with enhanced thermal properties”,
Constr. Build. Mater., vol. 38, pp.407–412, 2013.
[18] J.A.M. Ferreira, C. Capela, and J.D. Costa, “A study of the
mechanical properties of natural fiber reinforced
composites,” Fiber. Polym., vol.11, no. 8, pp.1181-1186, 2010.
[19] H. Sadeghi, and C. Rafati, “Construction Materials Laboratory,”
1st ed., Tehran, 2007, pp. 423-427.
[20] Gypsum binders and gypsum plasters, Definitions and
requirements, EN Standard 13279-1, 2009.
[21] Gypsum binders and gypsum plasters, Test methods, EN
Standard 13279-2, 2004.
)